鋁板使用前后應將板材存放于干燥通風處,且平放在平整的表面上,切勿踩踏、撞擊。除此之外，如果想順利使用鋁板完成高質量項目要多注意什么呢？下面鋁板生產廠家向你介紹。
Before and after use, the aluminum plates shall be stored in a dry and ventilated place, flat on a flat surface, and shall not be stepped on or hit. In addition, what should we pay more attention to if we want to successfully use aluminum plates to complete high-quality projects? The aluminum plate manufacturer will introduce it to you.
鋁板開槽:用開槽機或鑼機開槽時,應使用半圓頭式大于90度的銑刀.下刀既不要過深傷及鋁板,也不要過淺使折邊困難,應留有0.2-0.3MM厚塑料芯材連同鋁板一起彎邊,以增加強度和韌性,否則在彎邊時鋁板可能斷裂或漆膜爆裂。
Aluminum plate slotting: When slotting with a slotting machine or a gondola machine, a semicircle head milling cutter larger than 90 degrees should be used. The cutting tool should not be too deep to damage the aluminum plate, nor too shallow to make folding difficult. A 0.2-0.3MM thick plastic core should be left with the aluminum plate bent together to increase strength and toughness, otherwise the aluminum plate may break or the paint film burst when bending.
鋁板彎邊:彎邊時需用力均勻,一次成型,不要反復彎折,否則鋁板可能斷裂。
Aluminum plate bending: the bending force shall be uniform, forming at one time, do not bend repeatedly, or the aluminum plate may break.
鋁板弧形加工:加工弧形應使用專用彎曲設備加工,徐徐用力,使板材逐步達到所需的曲面.切勿一次彎曲成型。
Arc processing of aluminum plate.

鋁板批次:同一型號而不同批次的板材可能存在色差,出售和使用不同批次板材時應增加比對色差之程序，我們公司主要經營合金鋁板、鋁花紋板等，無視覺色差時方可在同一平面使用。
Aluminum plate batch: The plates of the same model but different batches may have color difference. When selling and using different batches of plates, the procedure for comparing color difference should be added. Our company mainly deals in alloy aluminum plates, aluminum pattern plates, etc., and can only be used on the same plane when there is no visual color difference.
鋁板安裝方向:將同色鋁板安裝在同一平面時,流程方向應一致,否則可能造視覺色差。
Aluminum plate installation direction: when installing aluminum plates with the same color on the same plane, the flow direction should be consistent, otherwise visual color difference may occur.
鋁板撕膜:應在鋁板安裝后的45天內撕去保護膜,否則可能發生撕膜困難或移膠現象。
Tearing film of aluminum plate: the protective film shall be removed within 45 days after the installation of aluminum plate, otherwise it may be difficult to tear the film or remove the adhesive.
鋁板使用條件也要明白，如內墻板應在室內使用,不宜安裝在室外,以保證使用效果和使用年限。更多相關內容就來我們網站http://www.yelang007.com咨詢了解吧！
The use conditions of aluminum panels should also be understood. For example, the interior wall panels should be used indoors rather than installed outdoors to ensure the service effect and service life. More relevant content will come to our website http://www.yelang007.com Ask and understand!